Hello guys, Welcome to Africa's Largest Video Search Engine, and you are watching Audi quattro AWD DIFFERENCES - Torsen vs Centre Differential vs Haldex vs Ultra. and this video is uploaded by GommeBlog.it: Tecnica e Performance at 2018-02-07T11:49:39-08:00. We are just promoting this video only for entertainment and educational purpose only. I hop you like our Video Search Engine. [mCbVd8mMUJw]
| Name | Audi quattro AWD DIFFERENCES - Torsen vs Centre Differential vs Haldex vs Ultra |
| Video Uploader | Video From GommeBlog.it: Tecnica e Performance |
| Upload Date | This Video Uploaded At 07-02-2018 19:49:39 |
| Video Discription | Audi Quattro DIFFERENCES - Centre Differential vs Haldex vs Ultra HOW IT'S MADE the AWD Audi System. Audi A1 - A3 - A4 - A5 - A6 - A7 - A8 - Q2 - Q3 - Q5 - Q7 - R8 - 4wd DSG or S-tronc - Manual Gearbox 00:00 - Audi quattro intro 00:45 - Audi quattro Self-Locking crow-gear (Gen VI) 06:52 - Audi quattro ultra 09:46 - Audi quattro haldex 12:55 - Audi quattro Viscous Coupling (R8) ► AUDI A4 - A5 - A6 - A7 - A8 - Q5 - Q7: Audi quattro with self-locking crown-gear centre-differential anq torque vectoring Audi debuted the 6th generation of quattro in the 2010 RS5. The key change in generation VI is the replacement of the Torsen Type "C" centre differential with an Audi-developed "Crown Gear" differential. With the new "Crown Gear" center differential, up to 70% of the torque can be applied to the front wheels while up to 85% can be applied to the rear wheels if necessary. The net result of this advance in quattro is the ability of the vehicle electronics to fully manage the vehicle dynamics in all traction situations, whether in cornering, acceleration, braking, snow or in any combination of these. This system was later adopted by the A7, latest generation of the A6 and A8. ► AUDI A1 - A3 - Q2 - Q3: Audi quattro with HALDEX Starting from 1998, the Swedish Haldex Traction LSC unit replaced the viscous coupling. Haldex is used by Audi on the quattro versions of the Audi S1, Audi A3, Audi S3, and the Audi TT. It is also used by Volkswagen in the 4motion versions of the Mk4 and Mk5 generations of Volkswagen Golf, Volkswagen Jetta, and the Golf R32, Volkswagen Sharan, 6th generation VW Passat (also based on the A-platform) and Transporter T5. On the Audis, the trademark holds, and are still referred to as quattro, whereas the Volkswagens receive the 4motion name. The Škoda Octavia 4x4 and SEAT León 4 and SEAT Alhambra 4 also used Haldex LSC, being based on Volkswagen Group models. Curiously, the Bugatti Veyron also utilizes Haldex, though with separate transmission, PTU and front and rear axles. ► Audi R8: Audi quattro with Viscous Coupling This 4WD system was used only on Volkswagen branded vehicles, and was never used on any Audi cars except Audi R8 model. A viscous coupling installed instead of a centre differential, with freewheel mechanism to disconnect the driven axle when braking. Normally a front-wheel drive vehicle (except Vanagon, see above). In normal driving conditions, 95% of torque is transferred to front axle. Because viscous coupling is considered to be "slow" (some time is needed for silicone fluid to warm-up and solidify), 5% of torque is transferred to rear axle at all times to "pre-tension" the viscous coupling and reduce activation time. The coupling locks when slipping occurs and up to near 50% of torque is automatically transferred to rear axle (front in Vanagon). In on-road conditions, the car will not move if one front wheel and one rear wheel lose traction. The freewheel segment, installed inside the rear differential, lets rear wheels rotate faster than front wheels without locking the viscous coupling and preventing ABS from applying brakes to each wheel independently. Because of the freewheel, torque can be transferred to rear axle only when the vehicle is moving forward. For four-wheel drive to work when reversing, a vacuum-actuated "throttle control element" is installed on the differential case. This device locks the freewheel mechanism when in reverse gear. The freewheel mechanism unlocks when the gear-shift lever is pushed to the right, past the third gear. The freewheel is not unlocked immediately after leaving reverse gear on purpose – this is to prevent the freewheel from cycling from locked to unlocked if the car is stuck and driver is trying to "rock" the car by changing from first to reverse and back. Disadvantages of this four-wheel drive system are related to actuation time of the viscous coupling. When cornering under acceleration on a slippery surface, the rear axle is engaged with delay, causing sudden change in the car's behaviour (from understeer to oversteer). When starting on a sandy surface, the front wheels can dig into the sand before all-wheel drive is engaged. ► If you love cars you should SUBSCRIBE Now to Gommeblog Car and Performance Youtube Channel: http://goo.gl/sP8oKK ► Gommeblog.it CAR TV and PERFORMANCE is a webzine devoted exclusively to the international world of automobile, car news, How It's made videos and Car Factory Production. SUBSCRIBE NOW and discover all new cars before anyone else! [mCbVd8mMUJw] |
| Category | Autos & Vehicles |
| Tags | audi | quattro | audi quattro | center differential haldex | haldex | torsen | how it's made | snow | awd | all wheel drive | 4wd | 4x4 | offroad | mud | four wheel drive | 4 wheel drive | wheel | cars | how | hill | car | q7 | how to made | car factory | car factory robots | vehicles | factory | dsg | how to make | made | how its made | making of | factory made | how to | audi a4 | production | gommeblog | luxury | safety | how it made | make videos | manufactory | audi quattro snow | control | power | perfect | a4 | differential | limited slip | esp |
