Hello guys, Welcome to Africa's Largest Video Search Engine, and you are watching Understanding the Toyota RAV4 Hybrid. and this video is uploaded by WeberAuto at 2021-01-23T14:06:11-08:00. We are just promoting this video only for entertainment and educational purpose only. I hop you like our Video Search Engine. [O61WihMRdjM]
| Name | Understanding the Toyota RAV4 Hybrid |
| Video Uploader | Video From WeberAuto |
| Upload Date | This Video Uploaded At 23-01-2021 22:06:11 |
| Video Discription | See the amazing hybrid transaxle used in the 2019 - 2022 Toyota RAV4 Hybrid. Learn how this incredible transaxle functions in all nine modes of operation to help its sophisticated 2.5L engine deliver almost 40% brake thermal efficiency (BTE) for maximum fuel economy. This transaxle is also used in the 2018 and above Camry Hybrid, Avalon Hybrid, Lexus ES300h hybrid, and 2021 Venza Hybrid. Corrections and Additions: 1. Addition: In EV mode, sling lubrication from gear movement is provided to drip channels that feed bearings, gears, and stator cooling. The RAV4 Prime uses an external electric oil pump for use in EV mode. 2. The 2021 Toyota Venza Hybrid also uses the P710 transaxle. 3. Correction: At 27 minutes: In overdrive with MG1 spinning backward, the ICE RPM should be less than when it is in direct drive. I incorrectly said the ICE RPM was higher. 4. Correction: The BTE chart at 23:06 is the wrong one for this ICE, it is for the non-hybrid ICE variant known as A25A-FKS (The related experiment is done by EPA, which provides all the details), while the engine for the Hybrid RAV4 is A25B-FKS with a slightly higher peak efficiency to 41%. The BTE plot of A25B is different from the A25A, with lower maximum torque, and a much larger high-efficiency area (it reaches 38% efficiency at 80 Nm until 2500 RPM), and the peak efficiency point/area is shifted to the left/downside. Thank you to viewer rt te for catching my error. EPA Report: https://www.epa.gov/sites/production/files/2020-08/documents/sae-2019-01-0249.pdf TIMELINE: 0:00 Start 0:09 Introduction 0:21 Model and vehicle usage 1:11 2.5L High-Efficiency Internal Combustion Engine (ICE) 1:35 The P710 transmission is used to keep ICE in its optimum RPM range 1:48 See the internal parts and functions of the P710 transaxle 2:00 Motor/Generator 2 2:40 Counter-driven gear and pinion gear 3:24 Final drive ring gear and differential 4:40 Overall gear ratio MG2 to Tires 6:00 MG2 Power, Torque, and RPM Ratings 7:02 MG2 motor and generator operation 8:00 MUST SEE Two Torque Paths to drive the vehicle 8:19 MG1 and the Power Split Device planetary gear set 8:50 Planetary gear set components 10:30 Ring gear connects to counter drive gear 11:25 Planet carrier connected to the ICE crankshaft 11:45 Sun gear connects to the MG1 rotor 12:01 Oil pump drive shaft 13:10 MG1 rotates the crankshaft to allow the ICE to start 13:40 Parking gear 14:23 MG1 has three functions 17:00 Underdrive, direct drive, and overdrive 18:00 The nine modes of operation of the electronic continuously variable transmission (eCVT) 18:46 Mode 1 "Ready" on with the vehicle stopped 19:28 Mode 2 Charging the high voltage (HV) battery with the vehicle stopped 20:39 Mode 3 Starting off and low-speed cruising on electric power only (EV Mode) 21:36 Mode 4 Starting off and low-speed cruising with a low SOC 22:25 Mode 5 Constant speed cruising (eCVT) operation 23:00 MUST SEE See the ICE RPM, power, and torque ranges for maximum ICE brake thermal efficiency (BTE) 25:17 Relationship between ICE and MG1 RPM to stay in the optimal ICE efficiency range while driving at 104 km/h (65 mph) 25:52 Underdrive example 26:35 Direct drive example at 1650 ICE RPM 27:00 Overdrive example MG1 stops rotating 28:08 MG1 rotates backward for additional overdrive or power generation 29:19 MG1 Power, Torque, and RPM Ratings 29:45 Mode 6 Constant speed cruising (eCVT) operation with low SOC 30:39 Mode 7 Full Throttle Acceleration 31:27 Mode 8 Deceleration and regenerative braking 32:22 Mode 9 Reverse 32:38 MUST SEE Rotor differences between P610, P710, and P810 transaxles 33:24 MUST SEE RAV4 Prime P810 MG2 rotor difference (51% more power and ~36.5mm thicker) 34:33 Motor Stators, stator cooling, and stator temperature 36:00 Transmission oil pump (ICE driven) 36:45 Motor resolvers (position, speed, and direction sensors) 37:17 Three-phase cable size differences between P710 and P610 transmissions/inverters 38:13 The RAV4 Q610 rear electric motor ABOUT US: Weber State University (WSU) Davis Campus - Automotive Technology Department - Advanced Vehicles Lab. A technical description and demonstration of the Toyota P710 hybrid transaxle. We teach current vehicle technologies to our automotive students at Weber State University and online. For more information visit: http://www.weber.edu/automotive This video was created and edited by Professor John D. Kelly at WSU. For a full biography, see http://www.weber.edu/automotive/J_Kelly.html Visit my other youtube channel https://www.youtube.com/user/vibratesoftware to see the amazing NVH app for vibration diagnosis! ADDITIONAL TRAINING FOR YOU Join us for hybrid and electric vehicle training with two online courses and in a 5-day on-campus boot camp with Professor John D. Kelly. See http://www.weber.edu/evtraining DONATE TO OUR DEPARTMENT Please consider a donation to the Department of Automotive Technology at Weber State University here: http://advancement.weber.edu/Automotive [O61WihMRdjM] |
| Category | Education |
| Tags | WSU | Weber State Automotive | Weber State University | John D. Kelly | Guy in Wheelchair | Professor Kelly | EV Boot Camp | Utah | Toyota | RAV4 Hybrid | RAV4 Prime | P710 | P810 | 40% BTE | BTE | Brake Thermal Efficiency | Venza Hybrid | Sienna Hyrbid | Highlander Hybrid | ES300h | Lexus | Layton Utah | WSU Davis |
